Kat Heaters Frost Plug Style Block Heater Installation
Question:
How to install In a 2001 Buick century 3.1
asked by: Pat V
Expert Reply:
The engine block heater I recommend is the Kat's Heaters Custom Engine Block Heater - Frost Plug Style - 120V - 400 Watts - 34 mm, # KH11415. It is a confirmed fit for your 2001 Buick Century 3.1. The easiest mounting location for your vehicle will be the center rear of your block. The element must face 9 o'clock position to avoid contact with engine wall.
This how you will install it.
1. Drain and flush radiator and block.
2. Remove correct frost plug or core plug - depending on type of engine.
3. Clean frost plug hole with a cleaning agent to remove any dirt, grease or paint. (Lubricate “O” ring with a light weight grease only, oil is not as satisfactory) before installing heater in frost plug opening.
4. Place engine heater in frost plug opening. Position of element is dependent on specific engine. The shoulder on the steel section of the heater must be against the face of the engine block wall. This allows the “O” ring to seal the unit for a leak proof installation.
5. Models with a toggle or flat cross bar on the back side of steel adapter must be installed with bar behind block wall. Tighten the Hex head or nut to 15 to 18 inch pounds torque until the cross bar is tight against inside block wall. Only use these models where recommended.
6. Models with a curved cross bar need to be torqued to 80 to 90 inch pounds to expand the cross bar on the back side of the heater in the frost plug opening. Only use these models where recommended.
7. Models with a butterfly cross bar need to be tightened to 14 to 19 inch pounds. Only use these models where recommended.
8. Place the electric cord from the heater through radiator grille or other convenient opening and tape or fasten in position, making sure it is clear of all moving parts (fan blades) and heater parts (manifold).
9. Refill radiator, run engine long enough to build up a maximum pressure and check for leaks to complete installation.
10. Connect the Kat’s Engine Heater to any 120 volt AC or DC electric outlet. Use your heater for 60 minutes or longer before vehicle is to be operated. Heater can be left on all night without overheating.
11. This heater is equipped with a three prong (grounding) plug and should be connected to a properly grounded circuit.
12. If an extension cord is used in conjunction with this heater, be certain that the wire size of the extension cord is of adequate size for the wattage of the heater and distance from the receptacle to the heater Consult a licensed electrician if further information is required.
Products Referenced in This Question
Kat's Heaters Custom Engine Block Heater - Frost Plug Style - 120V - 400 Watts - 34 mm
- Vehicle Heaters
- Engine Block Heater
- Frost Plug Style
- 400 Watts
- CSA Approved
- Kats Heaters
more information >
Product Page this Question was Asked From
Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts
- Vehicle Heaters
- Engine Block Heater
- Cartridge Style
- 400 Watts
- Kats Heaters
more information >
Continue Researching
- Shop: Vehicle Engine Heaters
- Shop: Dexstar Silver Modular Trailer Wheel - 16" x 6" Rim - 8 on 6-1/2
- Shop: Dexstar Steel Spoke Trailer Wheel - 16" x 6" Rim - 8 on 6-1/2 - White Powder Coat
- Shop: Dexstar Steel Mini Mod Trailer Wheel - 16" x 6" Rim - 8 on 6-1/2 - White Powder Coat
- Shop: Bumpers
- Shop: Westin Fey Diamondstep Rear Bumper with Custom Installation Kit - Chrome Plated Steel
- Article: Trailer Wiring Diagrams
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Choosing the Right Trailer Wiring
- Shop: Suspension Enhancement
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 25580
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Air Lift Air Spring Kit And Spacers Needed For A Lifted 2016 Ford F-150 With A Gooseneck Hitch
- Search Results: 10~36
- Video: Draw-Tite Front Mount Trailer Hitch Installation - 2018 Ford F-150
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Trailer Tire Sizing
- Search Results: air bags
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: Is RoadActive Suspension Kit Needed In Addition to Weight Distribution
- Video: Roadmaster Active Suspension Custom Leaf Spring Enhancement Kit Installation - 2018 Ford F-150
- Shop: Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Brake Controller
- Search Results: lug nut
- Search Results: am20750
- Shop: Towing Mirrors
- Article: Choosing the Right Suspension Kit for Your Truck and Trailer
on Vehicle Heaters
