What Is Outer Diameter Of Redline D-Washer For 6 To 8K Axle Spindles

Question

Question:

Good day, Im looking for a D washer for a spindle with the dimensions of 1/8 x 1inch I.D. x 2inch O.D. Does this washer have an outer measurement of 2 inches? Thanks for your assistance.

asked by: Richard

0

Expert Reply:

I went to the warehouse and measured the outside diameter of the Redline D-Washer, part # 5-57.

It does measure 2-inches as you asked about. This washer is designed for 6 to 8K axle spindles with a 1-inch diameter.

expert reply by: Jeffrey L

0

Answer 1

The DB-42 is an older style of UFP 3,500 lb axle disc brake components. The Kodiak kits like the part #K2HR35D will fit in replacement of that and would be an upgrade so this would be a great solution. It comes with everything you'd need to…

view full answer...

Answer 2

Based on the dimensions you listed the equalizer you need is the part #TREQE1. This equalizer has 7-3/4 inches between the mounting holes from left to right and 2-7/8 inches vertically.

view full answer...

Answer 3

It is tough to get a correct eye-to-eye measurement on a double-eye leaf spring when the spring is still installed in the suspension. It is much better to measure for a replacement leaf spring by removing it first. Also, if a spring is very old and…

view full answer...

Answer 4

The difference is the length of the equalizers that come with the kit. The part #K71-449-00 comes with equalizers that are 7-3/4 inches from eye to eye whereas the part #K71-359-00 has equalizers that are 2 inches shorter at 5-3/4 inches.

view full answer...

Answer 5

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 6

In order to retain your current suspension geometry, you'll need to use an equalizer of the same length and height as the 7-3/4 x 2-7/8 equalizer you currently have. The Dexter Axle #K71-449-00 offers equalizers that are the same width and height…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

You actually should shoot for 4-1/2" of clearance between the top of your tire and the bottom of the fender well. This accounts for flex in your suspension. Unless 2,280 lbs is the GVWR (gross vehicle weight rating) of your trailer then you need…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

What Is Outer Diameter Of Redline D-Washer For 6 To 8K Axle Spindles

Product Page this Question was Asked From

Continue Researching