Rhino Rack Ski and Snowboard Rack Compatibility with Square Crossbars

Question

Question:

I just ordered the square cross bars and I wanted to make sure that the clamps on this ski attachment will hold the square bars too. Is that correct or is there a different attachment needed?

asked by: Eric B

0

Expert Reply:

Yes, the Rhino-Rack Ski and Snowboard Rack # RR574 will attach to the Rhino-Rack 2500 Roof Rack that you ordered.

The Rhino-Rack # RR574 comes with a universal mounting kit that will attach to crossbar styles including round, square, elliptical, aero ,and OEM bars.

expert reply by: Jared P

0

Answer 1

If you install the Rhino Rack Ski Carrier #RR574 or #RR576 on a set of crossbars you add 6 inches to the bars.

view full answer...

Answer 2

The clamp-on mounting brackets for the Rhino-Rack Ski and Snowboard Carrier #RR574 are in a fixed position (this will be the case with any other ski carrier as well), but I did go out to our warehouse to measure their spacing. From the outside of the…

view full answer...

Answer 3

For the factory crossbars on your 2010 VW Golf I recommend taking a look at the Rhino-Rack Ski and Snowboard Carrier #RR574. I really like the Rhino-Rack products because they provide many of the same benefits and features of the higher-end units…

view full answer...

Answer 4

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 7

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 8

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 9

Tracks can absolutely be installed on the roof of your A.R.E. Truck Cap to provide a mounting system for a roof rack. For this I recommend the Yakima Tracks, which come in 42 inch #Y01126, 54 inch #Y01127, and 60 inch #Y01135 lengths. These tracks…

view full answer...

Answer 10

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Rhino Rack Ski and Snowboard Rack Compatibility with Square Crossbars

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching