Dimensions of Camco 90-Degree Water Hose Brass Elbow CAM22505

Question

Question:

Hi, may i ask what are the sizes of threaded part of CAMCO22505? is it 1/2inch inch or much bigger? Thank you.

asked by: Ferdinand E

0

Expert Reply:

The Camco 90-Degree Water Hose Brass Elbow # CAM22505 has the same 1-inch fittings and thread pitch as a standard garden hose. I went to our warehouse and measured the male and female ends and confirmed both have this nominal 1-inch size. Please refer to the linked photo that I prepared for you which shows this dimension.

expert reply by: Adam R

0

click to enlarge

Answer 1

If you are okay with drinking from a garden hose then the Camco Water Hose Brass Elbow #CAM22605 that you referenced would work well for you. It's made of the same material (brass), as the fittings of a garden hose so you would be just fine…

view full answer...

Answer 2

I pulled a sample of Camco Water Hose Brass Elbow #CAM22605 from our warehouse so that I could take its measurements for you. The inner diameters of the male and female ends are shown in the linked photo. On the male end the larger outer diameter…

view full answer...

Answer 3

The flexible Tank Wand part #A01-0187VP is going to be able clean better than the fixed since you can more easily push it down into plumbing and manipulate it to get it to clean where you want it than the rigid #A01-0184VP.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Dimensions of Camco 90-Degree Water Hose Brass Elbow CAM22505

Product Page this Question was Asked From

Continue Researching