Why Does Tow Hook of 2006 Dodge Ram Need Grinding to Install Front Hitch 65046

Question

Question:

The hitch wont fit my truck with out grinding the flared lip of the bracket that holds my tow hooks. Is this my only option???

asked by: Bruce S

0

Expert Reply:

Sounds like you have a Laramie trim level on your 2006 Dodge Ram 2500. We have found that the Laramie models require slight grinding of the tow hooks to allow the hitch part # 65046 to install. I wish there was a way around the grinding but it's the best option.

expert reply by: Jameson C

0

Answer 1

I may have another option for you, but the Curt Front Mount Trailer Hitch #31604 you were looking at only fits select 1994-2002 Dodge Ram Trucks so it will not fit your vehicle. Instead we have the Draw-Tite Front Mount Hitch #65046 which is a…

view full answer...

Answer 2

The recommended front hitch for your 2006 Dodge Ram 2500 is the Curt Hitch #C31017. It has never been tested with the Banks Super Scoop so it would be hard for me to say for certain. The best option I could recommend for you would be to check out the…

view full answer...

Answer 3

Yes, the Draw Tite front hitch part #65046 that you referenced is a confirmed fit for a 4 wheel drive 2006 Dodge Ram 2500/3500 like what you have. I attached an install video for this hitch for you to check out as well.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

For your 2007 Ram 3/4 ton, I'd recommend the Curt #C31017 which would mount to the underside of the frame members and would have the receiver tube sitting directly under the front bumper. I spoke with my contact at Draw-Tite who confirms that…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Why Does Tow Hook of 2006 Dodge Ram Need Grinding to Install Front Hitch 65046

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching