BoatBuckle Fishing Rod Carriers for Use on 2015 Chevrolet Silverado 1500

Question

Question:

Can you mount the boat buckle hold down to a truck shell or truck side wall? P.S. Great website and Expert Service, this site is definitely a Book Mark. Thanks again!

asked by: Ed R

0

Expert Reply:

The BoatBuckle Rod Hold-Down PLUS System # IMF15435 is intended for deck- or gunwale-mounting but it absolutely could be installed, using appropriate alternate hardware you'll supply, to other surfaces such as the inside of a camper shell. You'll just need to source sutable hardware for the particular material at the installation point (metal vs. fiberglass).

We also offer the RodBunk Deluxe Fishing Rod Carrying System for Trucks # IMF17727 which is shown in the linked video.

expert reply by: Adam R

0

Answer 1

Yes, you can use the RodBunk Deluxe Fishing Rod Carrying System #IMF17727 in your 2011 Honda Odyssey without drilling. It will attach to the clothing hooks up above the doors of the vehicle or to cargo tie downs already in the vehicle like in the…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 6

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 9

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 10

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 11

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...