What is the Complete Length of TrailSeal Tailgate Gasket, item # 834532001583

Question

Question:

Does the TR-201 fill the entire gap from side to side? The picture only shows its about half the width of the tailgate.

asked by: Jack J

0

Expert Reply:

The TrailSeal Tailgate Gasket, item # 834532001583, is 114 inches long 1-1/8 inches wide, and 5/8 inches thick. This seal is made of 1 continuous piece that covers the gap from one side of the truck to the other.

expert reply by: Robert G

0

click to enlarge

Answer 1

I have an answer for you. Without knowing the exact dimensions of the gaps on the vertical and horizontal portion of your 2022 Honda Ridgeline's tailgate, I cannot confirm for sure what tailgate seal will allow full functionality. That is because…

view full answer...

Answer 2

I called BAK industries to see if they had weight specifications for their tonneau covers. Unfortunately, they do not record these, but there is something that I can offer that might help. The BAKFlip F1, part #BAK72329, and the MX4, part #BAK48329,…

view full answer...

Answer 3

I spoke with the manufacturer, BAK Industries, and the correct kit for your BAKFlip MX4 Hard Tonneau Cover - Folding - Aluminum - Matte Finish #BAK48329 is the Replacement Mounting Hardware Kit for BAKFlip G2 Hard Tonneau Cover #BAKBK-200KIT. This…

view full answer...

Answer 4

The Pace Edwards SwitchBlade #311-SWC95A17 that you referenced has a pinch latch that you use to open in the middle of the cover (see attached picture). When you close it all of the way and then close your tailgate the only way to open the cover is…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The BTR and BT8 denotations refer to the spindle, not the trailer hub. The difference between a BTR and BT8 spindle is that the BTR spindle uses a 1.063" diameter L44649 bearing and the BT8 spindle uses a 0.99" diameter L44643 bearing. In…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Really it's going to boil down to which spindle type your Bayliner Capri has. The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles #AKIHUB-545-35-G-EZ-K will work with 3,500-lb Dexter E-Z Lube and etrailer Easy Grease trailer axles with #84…

view full answer...

Answer 12

I do have an option for you but the Stromberg Carlson 4000 Series 5th Wheel Louvered Tailgate part #VGD-10-4000 does not have a spot for the factory backup camera. Therefore you would either need to find a way to mount this yourself, go without, or…

view full answer...

What is the Complete Length of TrailSeal Tailgate Gasket, item # 834532001583

Product Page this Question was Asked From

Continue Researching