Dimensions of the T-Bolts of the Xadapt8

Question

Question:

What is the outer diameter?

asked by: Matt

0

Expert Reply:

For the # Xadapt8 the head is 3/4 inch square and 1/8 inch thick. The shaft of the long bolt is 2-3/8 inches long and the shaft of the short bolt is 1-3/8 inches long. The threads are M6.

expert reply by: Jameson C

0

Answer 1

The closet M8 T-bolt I could find with the dimensions you were after is the Replacement M8 T-Bolt for Thule Roof Rack Gutter Feet #853-0782. This T-bolt is a total of 2-3/16 inches long, has a head that is .7 inches square and it will fit in the…

view full answer...

Answer 2

While I personally prefer Yakima's products over many others for their looks, functionality, and customer support there is nothing wrong with going with TruXedo Elevate Truck Bed Rack System #TX96NV. If your RetraxONE XR doesn't have T-slots…

view full answer...

Answer 3

We did have a customer come back and tell us that the Tie-Down Kit for TruXedo Elevate Rack System #TH52FR did fit well in the tracks of their RetraxPro XR T-slots and they didn't mention it interfering with the opening of the tonneau so it…

view full answer...

Answer 4

We had a customer come back and tell us that the Tie-Down Kit for TruXedo Elevate Rack System #TH52FR worked on their Retrax tonneau cover rails so it would work for yours as well with the included hardware.

view full answer...

Answer 5

The TS (T-Slot) Rails for Truck Hero Elevate Rack System - Full Size - Short Bed - 72" - Aluminum #TH65FR utilizes the Tie-Down Kit for Truck Hero Elevate Rack System - Qty 4 #TH52FR. This is the directly compatible T-bolt, however is the T-Bolt…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Dimensions of the T-Bolts of the Xadapt8

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching