Function of Stabilizing Straps Recommended for Curt Trailer Hitch C11471
Question:
Curt Trailer Hitch code C11471 for Hyundai Elantra Touring 2010 Description of hitch says stabilizing straps are required for non-trailer loads e.g. bike rack. What exactly are stabilizing straps - tiedowns for the stuff youre hauling, or straps from the hitch itself to the car body or frame?
asked by: Mike P
Expert Reply:
The strap referred to for the # C11471 trailer hitch, part # 18050, would be used as an extra stabilizer for the bike rack or accessory. In the case of a bike rack, you would attach the strap between the upright bar of the bike rack and the trunk of your 2010 Hyundai Elantra Touring.
This # 18050 strap is recommended to prevent extra sway due to the low tongue weight capacity of the class I hitch, in order to maintain the hitch warranty and also to provide extra support to prevent damage to the vehicle frame, trailer hitch, or hitch accessory.
If you plan on towing a small trailer with your vehicle, you would additionally need wiring and a hitch ball. The # C11471 hitch includes a ball mount and pin and clip.
We offer custom wiring harness # 118473, which would plug in behind your vehicle tail lights. If your trailer uses a 1-7/8 inch hitch ball, you would use a ball like part # 19256, or you would use # 19258 for a 2 inch hitch ball.
I have included some additional information below, if needed.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Draw-Tite Receiver Location Relative to Rear Bumper of 2009 Hyundai Elantra
- Q&A: Trailer Hitch and Wiring Recommendation for 2020 Land Rover Range Rover Sport
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Availability of Hitch Cargo Carrier for a 2013 Hyundai Elantra
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Q&A: Towing Small Jon Boat with 2013 Hyundai Elantra GT
- Q&A: Will a 1up USA Aluminum Quik-Rack 1 Bike Rack Fit a Curt Class I Trailer Hitch on a 2002 BMW 330xi
- Q&A: Can You Carry More Than 2 Bikes Using a Class I Trailer Hitch
- Article: Flat Towing Package for 2010-2013 GMC Terrain
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Rooftop Cargo Carriers