Bearing Buddy Replacement Recommendation and How to Determine Replacement Bearings
Question:
I have a 1996[?] Gator boat trailer. I am looking to replace the current [rusting] Fulton Bearing Protectors with SS Bearing Buddies. While I am at it, I was planning on replacing the bearings and seals as well - its been at least 7 years since they were replaced. Question - The current bearing protector measures 1.980 inches when removed at the hub end. What other measurements do I need to ensure ordering the correct seals/bearings, etc.?
asked by: Blaise
Expert Reply:
I am confident we have the parts you will need, but knowing which Bearing Buddy you have on your hub does not guarantee that we know for sure what bearings your hub has. The Bearing Buddy you need is the part # BB1980A-SS.
I really wish there was a way to determine what bearings a trailer needed without actually pulling the wheel off and checking, but there isn't. The only two solution I have for you would be to remove the hubs and get the numbers that are stamped on the bearing or for you to remove the hubs and use a digital or dial caliper to measure where the bearings and seal ride (see pic).
With that info I can help you figure out what you need.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 1.98 Inch
- Bearing Buddy
more information >
Continue Researching
- Shop: Bearing Buddy Bearing Protectors - Model 1980A-SS w/ Auto Check - Stainless Steel (Pair)
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Galvanized
- Shop: Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern - 60" Long - 2,000 lbs
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Q&A: Correct Replacement Idler Hub for Trailer with L44643 Bearings and 4 Bolt Pattern
- Shop: Dexter Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern - 60" Long - 2,000 lbs
- Shop: CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 14" Wheels - Qty 2
- Shop: LED Combination Tail Light Kit for Trailers under 80" Wide - Submersible - Driver and Passenger
- Video: CE Smith Trailer Fenders - Top and Side Step - CE19504-2 Review
- Search Results: boat fender
- Q&A: Replacement Trailer Fender for 1999 Spartan Trailer with 14" Tires
- Shop: RV Exterior Lighting
- Q&A: Replacement Wheel for Shoreland'r Boat Trailer
- Q&A: Original Wheel & Tire Sizes Supplied on ShoreLandr Trailer Model B16750-12
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch
- Q&A: Does HBA-CAM Adapter Module for Hydrastar Electric Over Hydraulic Brake Actuators have 2 or 4 Wires
- Search Results: 68149
- Shop: Trailer Wiring
- Article: Trailer Tire Sizing
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Brake Controller
- Shop: Fifth Wheel Hitch