Will the Draw-Tite Ball Mount # 80248 Clear the Bumper on a 2016 Jeep Renegade.
Question:
Will Draw-Tite Ball Mount - 9-3/4inch Rise, 11inch Drop - 9inch Long - 3,500 to 5,000 lbs - 80248 fit on a Jeep Renegade with Curt Trailer Hitch Receiver - Custom Fit - Class III - 2inch - C13269 without hitting the bumper?
asked by: Seth G
Expert Reply:
I contacted my tech contact at Curt and the distance from the hitch pin hole on the Curt # C13269 hitch to the bumper is 4-1/2". The center of the hitch pin hole to the edge of the gusset on the Draw-Tite Ball Mount # 80248 is 5-3/4" which means this ball mount sticks out enough to where it will not hit the bumper on your 2016 Jeep Renegade in the rise or drop position.
If you are looking for a pin and clip for this ball mount, I recommend the Draw-Tite Pin and Clip # PC3. If you need a hitch ball, I recommend the 2" Hitch Ball # A-90 or the 2-5/16" Ball # 63840.
For a wiring harness, I recommend the Tow Ready T-One Wiring Harness # 118651.
I attached a review video for the Draw-Tite Ball Mount you may want to check out.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
2-5/16" Hitch Ball - 1-1/4" Diameter x 2-3/4" Long Shank - Chrome - 20,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2-5/16 Inch Diameter Ball
- 2-3/4 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 20000 lbs GTW
- Class IV
- Class V
- Draw-Tite
more information >
Draw-Tite Ball Mount - 9-3/4" Rise, 11" Drop - 9" Long - 3,500 to 5,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 11 Inch
- Rise - 10 Inch
- Fits 2 Inch Hitch
- 5000 lbs GTW
- Class III
- Draw-Tite
more information >
2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-5/8 Inch Shank Length
- 1-1/4 Inch Diameter Shank
- 10000 lbs GTW
- Class IV
- Class V
- CURT
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How Much Slack Is Needed In Trailer Wire Connection To The Tow Vehicle?
- Q&A: Torque Specs for 3500-lb 5-on-4-1/2 Dexter Hub/Drum 84546UC3
- Q&A: Replacement Trailer Hub/Drum for Part Number 2420801
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Q&A: How Much More Clearance Under Trailer Using Torsion Axle With Negative Angle
- Article: My Trailer Hitch Doesn't Fit
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Replacing a Dometic Sealand 210 With Dometic Full-Timer 510H
- Q&A: Repair Kit Fulton Wedge-Latch # F670801, Fits Fulton/Bulldog Couplers for 2-5/16 Inch Balls
- Q&A: Does Furrion Single Zone Controller part # FACC12SA-BL Have Dip Switches
- Article: Harvest Hosts
- Article: Trailer Maintenance Schedule
- Article: Flat Towing Package for 2014-2018 Jeep Grand Cherokee
- Article: Top Weight Distribution Hitches for a Buttery Smooth Ride