Availability of USA Manufactured Trailer Hub Drum Assemblies
Question:
Are these parts made in USA, or elsewhere?
asked by: Robert M
0
Expert Reply:
The AxleTek # AKHD-655-35-EZ-K hub is manufactured overseas in China. For a compatible hub/drum that's manufactured in the USA, take a look at the trailer hub and drum assembly, part # 84656UC3-EZ from Dexter Axle. This hub is compatible with the same L68149 inner and L44649 outer bearing, has the same 6 on 5-1/2 inch bolt pattern and has the same capacity as the AxleTek # AKHD-655-35-EZ-K.
expert reply by:
Mike L
0
Products Referenced in This Question
Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2
- Trailer Hubs and Drums
- Hub with Integrated Drum
- EZ Lube
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- Dexter
more information >
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 6 on 5-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- etrailer
more information >
Continue Researching
- Shop: Brake Controller
- Shop: Aluminum Sendel Series T07 Black Machined Trailer Wheel - 14" x 5-1/2" Rim - 5 on 4-1/2
- Shop: Electric Trailer Brake Assembly - Self-Adjusting - 10" - Right Hand - 3,500 lbs
- Shop: Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Video: Curt Brake Controller C51432 Review
- Shop: Trailer Hitch
- Q&A: How Far in a Trailer Hub Should the Grease Seal Go
- Q&A: Can a Trailer Grease Seal Be Pressed In Too Far Beyond Flush
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: safety chain snap hooks
- Search Results: safety chain hooks
- Search Results: spindle nut washers
- Search Results: brake adjustment tool
- Search Results: curt discovery
- Q&A: Where are the Bearings for the eTrailer Trailer Hubs Made
- Video: etrailer Trailer Brakes AKEBRK-35R-SA Review
- Video: etrailer Trailer Idler Hub Assembly Review
- Video: Dexter Axle Trailer Brakes 23-468 Review
- Video: Curt Safety Chains and Cables S-Hook with Wire Keeper Review
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-555-35-K Review
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Curt Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
- Q&A: Troubleshooting No Reverse Light Circuit Present at Rear of Truck 7-Way
- Q&A: Wiring Diagram for 7-Way Round Pin Trailer and Vehicle Side Connectors
- Search Results: hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Wiring