Will The Draw-Tite Class III Hitch Fit 2011 KIA Sorento SX
Question:
According to the dealer, an after market hitch is not available for the Sorento SX . The dealer has quoted $700+ for this. Can you please research? The SX model has reconfigured exhaust and a lower chrome trim plate. Thx
asked by: Dan H
Expert Reply:
Our representative at Draw-Tite has confirmed in the past that the Draw-Tite Trailer Hitch for the 2011 Kia Sorento, part # 75684 will fit the 2011 Kia Sorento SX models.
However, part # 75684 will not fit the SX models that have dual exhaust, or an exhaust tip on the driver side and the passenger side. This does not mean just dual exhaust tips on one side, but an exhaust tip on each side of the vehicle.
The Kia Dealership may just be unaware that there is an aftermarket hitch available for the 2011 Kia Sorento SX.
In addition to part # 75684, to complete your towing setup you may need a ball mount, hitch ball, pin and clip, and wiring. For a ball mount, hitch ball, and pin and clip, I would recommend the etrailer Ball Mount Kit, part # 989900. This is a kit which includes 2 ball mounts, a 1-7/8 inch ball, 2 inch ball, and a hitch pin and clip.
For trailer wiring, use # C56332 if your SX model has the Factory Tow Prep Package, or # 118506 without the tow package.
I have linked you to instructions for the parts I have recommended, as well as an installation video for you to check out.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Trailer Wiring Diagrams
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Comparing Curt # 13195 and Draw-Tite # 75908 for 2017 Kia Sorento
- Q&A: Finding the Serial Number on a Roadmaster Sterling Tow Bar to Use Adapter for Blue Ox base Plates
- Q&A: How To Determine if a 2011 Kia Sorento has the Factory Towing Prep Package
- Article: Roadmaster Vehicle Specific Base Plates
- Q&A: How to Tell if 2020 Kia Sorento Has Factory Tow Package
- Q&A: Is Drilling Required to Install Draw-Tite Trailer Hitch on 2012 Hyundai Santa Fe
- Q&A: How to Determine if a 2013 Kia Sorento has a Factory Towing Prep Package
- Article: How to Measure for Trailer Hitch Drop
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Hitch Receiver Sizes