Replacement Westin Hardware For Step Bars 23-0500

Question

Question:

I am looking for the brackets to install the Westin 23-0500 step bars on my 1992 Sierra 1500. Do you carry these, or can you get them? Thanks,

asked by: Robin S

0

Expert Reply:

Yes, what you need is the part # 23-050pk. This is the replacement hardware for the # 23-0500 bars you have that will fit your 1992 GMC truck.

expert reply by: Jameson C

0

Answer 1

The correct replacement hardware for your Westin E-Series Round Nerf Bars - 3" - Polished Stainless Steel #23-1680, is the Replacement Hardware for Westin E-series Step Bars #23-168PK.

view full answer...

Answer 2

For your 2006 GMC Sierra 1500 with Westin 3 inch diameter nerf bars the correct hardware replacement kit you'd need is the part #23-195PK.

view full answer...

Answer 3

The Aries Round Nerf Bars - 3" Diameter - Polished Stainless Steel #AA204018-2 are rated for a static weight of 500 lbs according to my tech contact at Aries.

view full answer...

Answer 4

Since the nerf bars are designed to fit specific vehicles, you'll need a specific mounting kit for the bars more than one for the vehicle. The good news is that the 2004 and 2006 Dodge Ram Quad Cab both used the same bars. If you have the Westin…

view full answer...

Answer 5

From the center of the tube to the center of the tube for the Westin E-Series Round Nerf Bars #23-0500 is measures 48" but then the overall length is 51". Please note that this is designed to fit various models of Yukon, Tahoe, Blazer, and…

view full answer...

Answer 6

I'd recommend the Curt Class IV hitch, part #C14081. When installed, the hitch will sit pretty tightly to the underside of the rear bumper, as would the Draw-Tite #41901 you looked at, but the Draw-Tite model only fits the long bed model truck.…

view full answer...

Answer 7

For your 1996 Chevy K2500 with a step bumper the B and W Hitch part #BWHDRH25124 is a confirmed fit. The distance between the mounting holes left to right is 34-1/2 inches. The spare will need to be temporarily moved to install this but it will be…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Replacement Westin Hardware For Step Bars 23-0500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching