What is Classic Accessories' DryGuard Fabric and Will DryGuard Cover CA20085 Fit 17-Foot Bayliner

Question

Question:

What material is DryGuard made of, and will part # CA20085 be a good fit for my 2007 Bayliner BR. Boat is 17foot 9inch long, w/o swim deck, and has a windshield.

asked by: Phil D

0

Expert Reply:

The 17-foot, 9-inch length of your 2007 Bayliner will be fine with the Classic Accessories DryGuard Waterproof Boat Cover # CA20085 so you'll just want to measure the boat's beam (width at the widest point) to confirm it does not exceed the 98-inch maximum for the cover. It will fit fine with your windshield.

If you find you need a slightly larger cover you can use DryGuard cover # CA20086 which fits boats up to 19-feet long and up to a 102-inch beam.

The DryGuard material is a 300-denier woven polyester fabric (PVC-free) that has a polyurethane coating and taped seams to make it waterproof. It is also resists mildew and UV-radiation.

expert reply by: Adam R

0

Answer 1

As long as your boat's beam (width of the widest point) does not exceed the 98 inches, the Classic Accessories DryGuard Boat Cover for 98" Beam #CA20085, it will fit your boat. I would not recommend choosing the larger size as boat covers…

view full answer...

Answer 2

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 3

The TruXedo Boat Windshield Cover #TX38FR places the polypropylene against the windshield to protect it from scratches. If you were to put the fabric side against the windshield it could hold particles of dirt and debris. While in tow the cover could…

view full answer...

Answer 4

The main difference between the two covers that you mentioned is the application for the two. The Classic Accessories DryGuard Waterproof Boat Cover #CA20085 is designed for bass and fishing boats whereas the Classic Accessories Boat Cover…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Since both a ST145/R12 size tire, like the Kenda Karrier S-Trail #AM10130, and a 5.30-12 size tire, like the Kenda K353 #AM10068, fit a 12 inch wheel, a ST145/R12 size tire can replace a 5.30-12 size tire. Keep in mind that these tires do have…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

What is Classic Accessories' DryGuard Fabric and Will DryGuard Cover CA20085 Fit 17-Foot Bayliner

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching