Dimensions of the CE Smith Fender Brackets # CE26098G-2

Question

Question:

Are you able to give the dimensions for the bracket, distance between holes mainly as done on the 8-12inch fender brackets.

asked by: Dillon B

0

Expert Reply:

On the CE Smith Fender Brackets # CE26098G-2 the long side of the bracket is 8-1/4 inches, the shorter side of the bracket is 6-1/2 inches, the bracket is an 1-1/2 inch in width, on the shorter side the holes of the bracket measure 4 inches, on the shorter side the holes measure 2-3/8 inches, each hole is 3/8 of an inch thick.

I attached a video that shows all of these measurements being taken.

expert reply by: Jameson C

0

Answer 1

Of the two options the Light Guard part #LG440NP is the way to go. It gives solid all around protection and does extend past the light offering protection for the lens. Check out the attached photo showing how the light fits into the housing and the…

view full answer...

Answer 2

We carry a Dexter 6K axle that comes very close to the measurements you specified. The #8327826-EB has an 86-1/2 inch hub face to hub face dimension, which means it would only be 3/4 of an inch longer on each side which should still work well for…

view full answer...

Answer 3

I do have a potential option for your trailer, however we do not have any standard axles that match the spring center and hub face lengths on your existing unit. If you don't want to go through a local trailer shop or fabricator to obtain a…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Tandem Axle Trailer Fenders w/ Backing Plates #HP32VR measuring 72" long x 9" wide x 20-1/2" tall is the closest thing that we have to those exact dimensions. These fenders are designed for…

view full answer...

Answer 5

Thanks for the photo. Honestly 5 inches of clearance from the fender to the top of the tire is fine if that is what you desire. We normally recommend 4 inches to allow for the suspension travel whether with leaf springs or torsion axles to allow…

view full answer...

Answer 6

Great question. As a general rule, when your trailer is loaded to it's full capacity, there should be a minimum clearance of 3 inches between the top of your tire and the underside of your fender.This should give you adequate clearance for…

view full answer...

Answer 7

Yes you certainly can. In order to bolt-on a set of metal weld-on fenders such as the Single Axle Trailer Fender part #HP29VR you will need a set of mounting brackets such as the Mounting Brackets for Trailer Fender part #CE26098G-2. If you do not…

view full answer...

Answer 8

I looked up pictures of your trailer and the most similar option we carry to the fender it has on it would be the #HP99VR which is the Jeep style of fender.

view full answer...

Answer 9

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 10

It looks like you got the CE Smith Single Axle Trailer Fenders w/ Top and Side Steps - Black Plastic - 13" Wheels - Qty 2 #CE19503-2. Assuming you have 13" wheels you did not order the wrong fenders. However, these do not come with mounting…

view full answer...

Answer 11

On the CE Smith Fender Brackets #CE26098G-2 the long side of the bracket is 8-1/4 inches, the shorter side of the bracket is 6-1/2 inches, the bracket is an 1-1/2 inch in width, on the shorter side the holes of the bracket measure 4 inches, on the…

view full answer...

Dimensions of the CE Smith Fender Brackets # CE26098G-2

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching