Availability of Replacement Drop Leg for Bulldog BD500188 Powered Trailer Jack

Question

Question:

Can u tell me what the part number is for the replacement drop leg for the BD500188?

asked by: Candace

0

Expert Reply:

Sure, I'd be happy to help you with that! You'll need part # BD500190, which is a replacement drop leg for the Bulldog # BD500185, # BD500187 and # BD500187.

expert reply by: Mike L

0

Answer 1

Accuracy is the most important thing when it comes to tongue weight scales in my opinion and convenience is a plus. The etrailer Tongue Weight Scale #e99044 is both. I have gotten my hands on this product and used it. One of my favorite things…

view full answer...

Answer 2

There might be a slight difference between the tongue weight reading if you measured it at the hitch ball with the etrailer tongue weight scale #e99044 and the trailer jack leg but the difference would be small enough that it wouldn't…

view full answer...

Answer 3

A general rule of thumb with regards to a weight distribution system is that one is recommended whenever the trailer is heavier than half the tow vehicle's weight. The Cherokee Wolf Pup 16BHS can weigh as much as 3,877 pounds fully loaded, while…

view full answer...

Answer 4

Great question. You technically could connect the Bulldog Powered-Drive Trailer Jack - Drop Leg - A-Frame - 21-3/4" Lift - 3,500 lbs - White #BD500188 to your vehicle lights, but we do not have the connector you would need to just plug into your…

view full answer...

Answer 5

There is a Bulldog jack that has numerous bolt holes to allow you to unbolt the jack and rotate it 90 degrees, the Bulldog Powered Drive Trailer Jack #BD500199. You can see an example of this in the linked video - just forward to about the 6:15 mark.…

view full answer...

Answer 6

I went out to our warehouse to assist with the dimensions of the Bulldog Powered Drive Trailer Jack - Drop Leg - A-Frame - 14" Lift - 4,000 lbs - Black #BD500199. From the top of the mounting plate to the bottom of the motor housing is 12-7/8…

view full answer...

Answer 7

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 8

The Firestone Ride-Rite Air Helper Springs #F2609 is the only kit that we have that will fit your 2020 GMC Sierra 1500 Denali with the adaptive ride control. These have a 5,000lb capacity to enhance your factory suspension under load. This will not…

view full answer...

Answer 9

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

It sounds like you're saying it is hooked up to power but it doesn't have the ability to raise the trailer. This could be the batteries or a problem with the wiring. It is probably getting power, it just may not be enough to lift the trailer.…

view full answer...

Answer 12

Your typical electric jack is designed to fit an A-frame so the only one we carry that is a side mount is the Fulton XLT #F141401. However, you may be interested in the Trailer Valet JXS Drill Powered Swivel Trailer Jack #TV64FR. This jack has a hand…

view full answer...

Availability of Replacement Drop Leg for Bulldog BD500188 Powered Trailer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching