Replacement Dual Latch Kit for TruXport Soft Roll-Up Tonneau Cover TX277601 on 2006 Ford F-150

Question

Question:

Will this part work for a 2006 ford f150 tonneau?

asked by: Chris

0

Expert Reply:

The TruXedo Replacement Dual Latch Kit for TruXport Soft Roll-Up Tonneau Covers, part # TX1117755, is a correct replacement part for the TruXport tonneau cover # TX277601 that fits your 2006 Ford F-150 with 5-1/2-foot bed as long as your cover was produced after April 2011.

expert reply by: Adam R

0

Answer 1

The Replacement Dual Latch Kit for TruXedo TruXport Soft, Roll-Up Tonneau Covers - Post April 2011 #TX1117755 does not have any way to adjust the spring. You can't tighten or loosen the spring.

view full answer...

Answer 2

To install replacement latches #TX1117755 you will need to remove the tailgate header rail from the side rails. Then you would remove the one fastener per latch holding the old ones on. Next slide off the old latches, slide the new ones into place,…

view full answer...

Answer 3

Thanks for the picture of the rear latch you have! From that I can tell that the #TX1117755 that you referenced is the correct kit.

view full answer...

Answer 4

TruXedo doesn't sell the latches individually, but you can get a pair of them as part #TX1117755. I passed the photo you provided along to my TruXedo representative, who confirmed that the #TX1117755 latches are the correct replacement part.

view full answer...

Answer 5

There are a pair of TruXedo TruXport tonneau covers that fit a 2003 Ford F-150 with a 6-1/2 foot bed and they will have different replacement cover. The #TX258101 is for non-stepside models and uses replacement tarp #TX2486-CVR while #TX248601 is for…

view full answer...

Answer 6

The replacement latch #TX1117755 will fit if your tonneau cover was manufactured after 2011. This is based on when your TruXedo TruXport Soft, Roll-Up Tonneau Cover #TX277601 was made and not the year of your 2008 Ford F150. Replacement latches for…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...