Height of the Shank that Inserts Into B and W Hitch on the BWGNXA2025

Question

Question:

what is the length of the 2 1/2inch square part?

asked by: Lucie

0

Expert Reply:

The height of the square part the slides into the gooseneck hitch on the part # BWGNXA2025 measures 4 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Reese Elite Series 3-Inch Gooseneck Hitch Ball #RP19314 is intended for the Ford and Ram factory gooseneck hitches but for the factory hitch in your 2017 GMC Sierra 3500, which is made by Curt, we do not have a 3-inch ball. I confirmed with Curt…

view full answer...

Answer 2

I checked with my contact at the manufacturer regarding the Over the Seal Strap Hinge #PLR2116. It does not have a particular weight rating. This unit is designed to bridge door molding or a door seal. It is made in the USA and made from high quality…

view full answer...

Answer 3

I attached a picture that has as many of the dimensions as I could think of for the #BWGNXA2025 that I could think you might want.

view full answer...

Answer 4

The 3" Hitch Ball for B&W Turnoverball Gooseneck Trailer Hitch #BWGNXA2025 does have a rating of 40,000lbs. Be sure to verify that you do not exceed any weight ratings for your vehicle or hitch system. I have included an image sent if from…

view full answer...

Answer 5

The 2-5/16" Gooseneck Coupler Head #291300 that you referenced is a gooseneck hitch coupler. It could be used with a tripod stabilizer if you had one but it's main function is for connecting a gooseneck trailer to a gooseneck ball in the bed…

view full answer...

Answer 6

The shaft of the B&W Turnoverball Adapter, #BWGNXA4025, measures 4-1/4 inches long from the base and it is 2-1/2 inches by 2-1/2 inches square. This adapter was specifically designed to fit in a B&W Turnoverball gooseneck trailer hitch.

view full answer...

Answer 7

The 2-5/16 inch Gooseneck Coupler Head with 1/2 inch Lock Pin, 30,000 lbs., item #291300, is cast construction and will require that a qualified weldor with experience in welding cast materials be utilized to attach the coupler to your equipment.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...