Width of the Opening on of the Curt S-Hook # C81820

Question

Question:

the area where I hook my chains has an exceptionally long reach. Most all of my trailers chains with not hook in except my 2007 rockwood windjammer that has a hook like the C81820. Can you tell me the dimension of this hook? or it will work on a Denali HD? Thanks

asked by: Roger

0

Expert Reply:

The opening on the Curt S-Hook # C81820 measures 3/4 inches. Overall length is 4-1/8 inches. I attached a picture that shows this dimension as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The openings on the Safety Chain S-Hook - 11/32" #4380 are .736" on bigger end and .416" on the smaller end. I attached a photo for you.

view full answer...

Answer 2

I went out to the warehouse and took several measurements of Curt Hook with Spring Loaded Safety Latch #C81840 for you. I have included a picture showing the measurements.

view full answer...

Answer 3

Since the Curt S-Hook with Wire Keeper for Safety Chains and Cables, part #C81820 is made of 7/16 inch diameter zinc coated steel, I recommend using something like a vise or channel locks if available to crimp the end around your safety chains. If…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Width of the Opening on of the Curt S-Hook # C81820

Product Page this Question was Asked From

Continue Researching