Boat Trailer Jack Recommendation for Older Boat Trailer

Question

Question:

I have an old boat and getting a used trailer that needs a trailer jack. I have no idea what the weight is looking for some suggestions. 18 ft old wood/fiberglass v hull w/ 70 hp johnson OB Trailer is steel, hold 19 ft boat what jacks do you reccomend

asked by: Mike

0

Expert Reply:

For your boat trailer the weld-on Fulton jack part # FTJ120W0301 would work well as it has more than enough capacity at 1,200 lbs.

If you would rather not weld the jack on and would prefer a bolt on setup the part # FTJ12000101 is similar and would also work well.

expert reply by: Jameson C

0

Answer 1

The rack and post assembly that you will want for your Bulldog jack is part #BD018006. This is the replacement rack and post assembly for the Bulldog Rack-and-Gear Bolt On Jack, #BD169201, which is what you have on your trailer. I spoke with my…

view full answer...

Answer 2

I attached a picture that details how to disassemble the Bulldog 12,000 lb jacks.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Boat Trailer Jack Recommendation for Older Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching