Parts Needed for 2005 Ford Ranger to Tow Trailer with Electric Brakes

Question

Question:

I have a 2005 Ford Ranger that has trailer wiring for a flat 4 plug. I have a trailer that has brakes, and the round style plug that I want to tow. I know that I will need a trailer brake controller and a plug for the back. I was looking at the Tekonsha 90185 and the Hopkins 4 Pole to 7/4 Pole adapter. I also see that there are some wiring harness kits that speed the installation of the Tekonsha unit by allowing you to plug directly into the vehicle wiring under the dash and then into the back of your controller. Is there a specific part that I need that will fit my truck? I didnt see it listed. Are there any other items I might need for my project?

asked by: Dale B

0

Expert Reply:

I am happy to help you with the parts needed in order to tow your trailer with electric brakes. You are on the right track with the products that you referenced. Some vehicles allow for custom wiring adapters to install a brake controller, but there is no such wiring harness adapter for your 2005 Ford Ranger. The Ranger does not have a port available under the dash with the functions needed for the brake controller pre-ran. You will want to hardware the installation of the brake controller.

To provide you with the Hopkins 7-Pole and 4-Pole Wiring Adapter as well as all of the additional hardware needed to install the brake controller, I recommend using the # ETBC7 kit. This kit will work with your existing 4-Pole trailer connector. I have attached the installation instructions and an installation video of this kit on a similar Ranger as yours.

The brake controller I recommend for you is the newer model to the Prodigy controller you referenced. I like the Tekonsha Prodigy P2 Trailer Brake Controller # 90885. This controller is a proportional brake controller that will apply your trailer's brakes in proportion to the braking of your Ranger. Some upgrades of this controller from the previous version are compatibility with electric over hydraulic trailer brakes as well as the automatic leveling capability when mounted within a 360-degree vertical range. This controller is featured in the installation video I have linked for you. I have also attached a review video of this controller for you.

expert reply by: Victoria B

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...