Coupler Lock Recommendation for a Bulldog Collar Lok Coupler

Question

Question:

Will this work on Bulldog hitch ?

asked by: Jerry B

0

Expert Reply:

The Bulldog couplers are usually the collar-lok style couplers so you would need to go with a different coupler lock than the # BLTL-33 that you referenced.

Instead you would wan the part # BLTL-20-40D as it is specifically designed for collar lok Bulldog coupler. I attached a review video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Pushing the pin back into the breakaway switch should allow the brakes of the trailer to release. You may have to back the trailer up slightly to get the brakes to release. If you have tried that and are still having problems you may need to…

view full answer...

Answer 2

I attached a picture that shows what type of lighting requirements are needed for a trailer over 80 inches in width as well as a link down below that covers this as well.

view full answer...

Answer 3

We have a solution that will work great but the part #BLTL-20-40D would not be what you'd need as it is designed to fit a Bulldog Collar Lok coupler and is only 3-3/16 inches wide. The #FA86-0015-318 would instead be what I recommend as this…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are…

view full answer...

Answer 12

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Coupler Lock Recommendation for a Bulldog Collar Lok Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching