Curt TriFlex C24VV Brake Controller Displays 9.9 With Brake Pedal When Trailer is Disconnected

Question

Question:

Just installed new trifex control in a 2011 GMC Sierra. Flashes 9.9 when I apply the brake. No trailer hooked up

asked by: Wayne

0

Expert Reply:

The fact that your Curt # C24VV TriFlex brake controller is displaying 9.9 on the LED display doesn't indicate a problem, it's perfectly normal and indicates the controller is working properly, according to the instructions.

On page 5 of the instructions, it states that if a trailer isn't connected the output setting (adjusted using the dial on the controller, adjustable from .5 to 9.9 is flashed on the display when the brake pedal is pressed or the manual brake switch is pressed.

I've provided you with a link to the brake controller instructions and to a photo of page 5 of the instructions. I'll also link you to some other helpful information about brake controllers.

expert reply by: Mike L

0

click to enlarge

Answer 1

The flashing output of a Curt Triflex normally indicates that the brake pedal is pressed but a trailer isn't connected. Since yours is flasing all the time that would indicate that you most likely have a short between the 12 volt power wire for…

view full answer...

Answer 2

Some models of the 2016 Chevrolet Express Van have the brake controller connection wiring taped and tucked under the driver side floor mat up towards the firewall, which sounds like what you have especially since they are labeled as such. The brake…

view full answer...

Answer 3

If your 2018 Chevy Express 3500 van does not have the tow package, you'll have to run the wires for the brake controller yourself since there are no existing wires. The signal for the brake controller on your 2018 Chevy Express 3500 don't use…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You do have the option to utilize the air brakes on your 2023 Freightliner Cascadia to control electric trailer brakes using the Hayes Air Actuated Trailer Brake Controller, part #HA100400C. However, we mostly recommend just using an electric brake…

view full answer...

Answer 9

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 10

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 11

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Curt TriFlex C24VV Brake Controller Displays 9.9 With Brake Pedal When Trailer is Disconnected

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching