Possible Replacement Trailer Bushing for 3/4inch ID X 7/8inch OD

Question

Question:

My bushing in the center has worn out. It looks like 3/4inch ID X 7/8inch OD. Do you have replacement bushings for the center?

asked by: Jason S

0

Expert Reply:

Since the size you listed isn't a standard trailer suspension bushing you most likely are in need of a 9/16 inner diameter, 7/8 outer diameter bushing like part # TRBU11568.

expert reply by: Jameson C

0

Answer 1

Harbor Freight trailers do not typically use standard hubs or spindles. In most of the situations that we have encountered, we do not carry a hub that uses the same bearings and seal that Harbor Freight uses. The best way to determine if we have a…

view full answer...

Answer 2

The 2,200 pound axles that I have seen all had a spindle washer. It is possible that your trailer didn't come with one but it is unlikely. The ends of your spindles are likely 1 inch in diameter since it is a 2,200 pound axle so you can use…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Possible Replacement Trailer Bushing for 3/4inch ID X 7/8inch OD

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching