Lube Plate Recommendation for Reese 30032 Fifth Wheel Hitch

Question

Question:

Which 5th wheel lube plate will fit my Reese 30032 5th wheel hitch?

asked by: Paul L

0

Expert Reply:

The recommended lube plate for the Reese fifth wheel hitch 30032 is the part # RP83002. I attached a review video for this product for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Answer 2

For your 2019 Chevy Silverado 2500 with the short bed and factory rail kit I highly recommend the B&W Companion OEM 5th Wheel Hitch w/ Slider #BWRVK3770. The Companion line is considered by many to be the best hitches on the market and this…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

While it is recommended to use a sliding 5th wheel for a short bed truck so that you have plenty of clearance for sharp turns, it is not necessarily required as it depends on your truck and trailer configuration. If you are using the same trailer…

view full answer...

Answer 11

Hey Clint, you are going to be installing the rail kit on the truck as well, correct? The Demco Recon 5th Wheel Trailer Hitch #DM47YV by itself should take only about 30 mins to assemble and install. The Installation Rail Kit #DM8551000 will also…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Lube Plate Recommendation for Reese 30032 Fifth Wheel Hitch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching