Width of the Angled Cone Section of the Americana Trailer Wheel Lug Nut # AM90070

Question

Question:

the 6o degree angle on my nut measures 3/8 of a inch. what do these measure?

asked by: David

0

Expert Reply:

I went and pulled a Americana Trailer Wheel Lug Nut # AM90070 from our warehouse to get the dimension you are looking for and found that the angled section measures 3/8 of an inch.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We have the exact size you are looking for with the Lionshead Lug Nut #LHLR103 which is for a 1/2 inch diameter wheel stud and has a 3/4 inch outer diameter. I would not recommend the lug nuts you referenced as they most likely would not fit into the…

view full answer...

Answer 2

We have the Americana Trailer Wheel Lug Nut - 7/8" Diameter - Stainless Steel - 1/2" - 20 #AM90070 which have the same look, threading, and outer diameter. The length of the nut is the only difference. Your current lug nuts are 1-7/8 inches…

view full answer...

Answer 3

I'd recommend sticking with what you've got currently. If the shocks feel a little light they may be worn and need replacing. The 052-003-00 part number you gave comes back to a part number from Dexter Axle, and while we do not carry a direct…

view full answer...

Answer 4

When adding wet bolts like what come with the Dexter Heavy Duty Suspension Upgrade Kit for Single Axle Trailers - Double Eye Springs #K71-358-00 you should always follow what the manufacturer's instructions are. You are correct that…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

That spindle looks pretty well destroyed so best option is going to be to replace the axle. You are going to need to measure your current axles in a few places to get the correct one as we don't have access to what your numbers reference. You…

view full answer...

Answer 12

Generally speaking, the lube plate will need to cover the skid plate on the 5th wheel hitch. There are some pin boxes out there that will recommend a specific lube plate but most of the times this classification will be from the 5th wheel hitch…

view full answer...

Width of the Angled Cone Section of the Americana Trailer Wheel Lug Nut # AM90070

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching