Curt Class III Hitch Part # 13538 for 2008 Sante Fe

Question

Question:

do you know if the hitch crossbar is hidden like the hidden hitch model? Do you know if the hitch will prevent the spare tire from being removed? Also, are the bolts tempered steel and at what rating? Ive heard of hitches coming with cheap bolts that have sheared off. Thanks.

asked by: Chris M

0

Expert Reply:

When installed on a 2008 Hyundai Santa Fe, the Curt Class III Hitch part # 13538 would look much the same as the Hidden Hitch model for that vehicle.

The center of the cross tube section would be mostly concealed by the rear fascia, with the receiver and the end portions of the cross tube that curve around the dual exhausts being visible.

The installation instructions do not mention the necessity of removing the spare tire, although removing it temporarily during installation can provide more working room.

The mounting bolts are Grade 5 bolts hardened steel. If properly tightened to the torque specifications provided by the hitch manufacturer, you should experience no problems with the hardware.

expert reply by: Mike L

0

Answer 1

The best and fastest way to clean out rusty weld nuts where a hitch installs on a vehicle frame is with a thread tap. This is a very common issue and the problem is that dirt and rust accumulates in the weld nuts making it seem like the bolts are too…

view full answer...

Answer 2

What you are most likely experiencing is weld nuts on the vehicle that are packed with corrosion and/or road grime. This happens on any vehicle that has seen at least 1 winter. What you will need to do is clean out the weld nuts so the bolts can be…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Curt Class III Hitch Part # 13538 for 2008 Sante Fe

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching