Replacement Cap for Trailer Brake Actuator

Question

Question:

I recently had to bleed my brakes and I didnt fasten the black cap on actuator and need to find a replacement because it was lost on my test drive. Do you guys sell those

asked by: Earnie J

0

Expert Reply:

We do offer replacement parts for many brands of brake actuators. The linked page will show you all brake actuator parts, including caps. Just click on caps to see these replacement parts for Titan, Atwood, Demco and Dexter couplers. For example, for the popular Titan model 10 and model 20 actuators you can use part # T4830601.

expert reply by: Adam R

0

Answer 1

The Titan Replacement Master Cylinder Cap #T4830600 that you referenced has a specific application on the Titan BrakeRite brake actuator. We also offer Replacement Master Cylinder Cap #T4830601 which fits their model 10 and model 20 actuators. I have…

view full answer...

Answer 2

I was able to contact Hydrastar for the following dimensions to help you compare. The Replacement Filler Cap for HBA-Series Hydrastar Actuators #HBA-BC uses 3 locking tabs. The tabs themselves are 1/4" and are 1" apart, located in a direct…

view full answer...

Answer 3

It's hard to tell which cap you need exactly from the picture but I measured the caps we have that might work for you. Part #T4480701 for Titan Model 60 actuators measures 1-1/4 inches at the threads like you previously saw. Part #T4830601 for…

view full answer...

Answer 4

Trailer hub and drum assembly #8-201-5 does match your bearings. I am fairly certain you have 5,200 pound axles and not 3500 pound axles since all of the parts you need are for higher rated axles than 3500 pounds. The races come already pressed into…

view full answer...

Answer 5

We sell replacement parts for the Titan Model 10 Surge Coupler #T2404600 that you referenced, but we do not offer a rebuild kit with all of the parts packaged together. For a replacement master cylinder assembly you would want the Replacement Master…

view full answer...

Answer 6

Sounds like you need the orifice fitting gasket part #T0774500 and the replacement cap part #T4830601 for your Titan Model 10 actuator.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Replacement Cap for Trailer Brake Actuator

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching