Availability of Replacement Brake Pads for a Titan Disc Brake Caliper

Question

Question:

I am looking for Brake pad Part Numbers for Titan 250 calipers . Are they the same as Kodiak pads ?? Thanks

asked by: Lou B

0

Expert Reply:

For Titan replacement brake pads we offer the part # T4870900 which will fit the Titan 10 and 12 inch disc brake assemblies made by Titan.

I couldn't find info on the 250 model calipers, but if you have a 10 or 12 inch assembly this would fit and work well.

expert reply by: Jameson C

0

Answer 1

If you have a Lippert 7k axle the Dexter Nev R Adjust Assemblies part #23-464-465 will fit and work well. Dexter and Lippert brake assemblies are made to the same dimensions and bolt pattern so they can be interchanged.

view full answer...

Answer 2

When Titan still made brakes the components for them were Kodiak. Since you had 250 calipers before then you can use the Kodiak calipers #KDBC250D as replacements if you want to. I have linked a video showing the features of this product for you.

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Availability of Replacement Brake Pads for a Titan Disc Brake Caliper

Product Page this Question was Asked From

Continue Researching