What Is Thread Size Of Bolt On Surco Replacement Bolt & Locking Knob

Question

Question:

Can you tell me the diameter and thread size of the stud? For example, is it 5/16inch diameter x 18 threads per inch? Thanks!

asked by: Cliff

0

Expert Reply:

I called my contact at Surco and they told me the Replacement Bolt & Locking Knob, part # SPN-104 is a 3/8 inch diameter bolt and it has 16 threads per inch.

This is a replacement knob for a Surco Bike Rack, 51953.

expert reply by: Jeffrey L

0

Answer 1

Yes the thread size of the knob part #TH79JV is M8 so it is perfectly compatible with the T-bolt part #853-0782 that you referenced.

view full answer...

Answer 2

The correct replacement locking knob for a Thule Apex 4 Bike Rack 9025 is the Replacement Locking Knob part #TH79JV. In order to switch over the lock core from the old knob to the new knob you'll need the Change Key part #853-1251. In regards…

view full answer...

Answer 3

The Thule TracRac SR Sliding Truck Bed Ladder Rack #TH43002XT-781 is a fit for your 2018 Chevy Silverado with 6-1/2 foot bed. The Thule Hull-A-Port Kayak Carrier w/Tie-Downs - J-Style - Fixed - Side Loading #TH834 is compatible when using the…

view full answer...

Answer 4

We have the replacements for the knob of your Thule Apex XT, part #TH9024XT, here. For the knob itself, you will need the Replacement Locking Knob for Thule Bike Racks, part #TH79JV. I've linked to a video review of this below. Since you…

view full answer...

Answer 5

We do have replacement locking knob #SR0018 that is the complete assembly with the threaded bolt, washers, and keys for the Hitch n Drive bike racks. The T-shaped knob and bolt together is not available.

view full answer...

Answer 6

Typically the lock will need to be in the unlocked position in order to unscrew the Locking Anti-Rattle Knob for Thule Apex Bike Racks and Rain Gutter Foot Packs - Qty 1 #753-0073 from the locking hitch pin. If your lock was in the locked position…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

What Is Thread Size Of Bolt On Surco Replacement Bolt & Locking Knob

Product Page this Question was Asked From

Continue Researching