Replacement Shank Bushing Recommendation for a Yakima HighLite Bike Rack Shank

Question

Question:

Hello, I am looking for the plastic washer type part- this part has cracked and then fell off. The bike rack is not very smooth without these. Is there any way I can order just these plastic pieces ?

asked by: David H

0

Expert Reply:

We have the part you are looking for. For the replacement bushing for the Yakima Highlite Y02439 you would want the part # 8890236.

I attached the picture you submitted as well that shows the bushing highlighted.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went to our warehouse to measure Thule Hitching Post Pro #TH934XTR and the height of the vertical arm is 32-1/8 inches long. See the diagram I included. I also measured from the center of the shank to the top of the vertical bar. It measured 33-3/4…

view full answer...

Answer 2

The Yakima adapter, #Y8890174, is designed to fit certain Yakima bike racks, and probably will not be compatible with your Thule rack. If you can get me a model number for the bike rack, I can contact Thule to see if they have anything that will…

view full answer...

Answer 3

If you have a DoubleDown Ace then you would need adapter #Y8890342 and not #Y8890174 which is for the original DoubleDown (the Ace models came later). That is the issue, just need to use the proper adapter for Ace models, #Y8890342.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Replacement Shank Bushing Recommendation for a Yakima HighLite Bike Rack Shank

Products Referenced in This Question

Continue Researching