Is 10-19 Grease Seal Acceptable Replacement for 17413 Seal on Shorelandr Boat Trailer

Question

Question:

I have a 1990 Shorelandr R1824 trailer that specifies the parts in your BK2-100 bearing kit except for the dust seal. For the dust seal it calls for a C/R 17413 Shorelandr part. Is the dust seal in the BK2-100 kit PN 10-19 an acceptable substitute? Thanks!

asked by: Jim C

1

Helpful Expert Reply:

According to my research, the 17413 grease seal would fit a 1.75 inch shaft, and has an OD of 2.565 inches. The 10-19 is very close, with an ID of 1.719 inches, but it's not close enough to be an acceptable substitute. Boat trailer manufacturers are well known for using oddball or proprietary parts.

The # 17413 seal you referenced is readily available online, and we offer the other components of the # BK2-100 kit individually:

Outer bearing # L44649
Inner bearing # L68149
Outer race # L44610
Inner race # L68111
Spindle washer # 5-101
Cotter pin # 165649

expert reply by: Mike L

1

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 10

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 11

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Is 10-19 Grease Seal Acceptable Replacement for 17413 Seal on Shorelandr Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching