Distance Between Mounting Holes on the Junction Box part # 38656

Question

Question:

Can you tell me what the measurement is between the center of one mounting hole to the center of the other mounting hole. Wanting to place in pre-existing holes and need to make sure they measure the same hole distance.

asked by: Brent M

0

Expert Reply:

The mounting holes of the Junction box part # 38656 that you referenced are 7-3/8 inches apart and are 1/4 inch in diameter.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Spectro Junction Box part #38656 can have a 12 volt accessory circuit added to it so that you could put a maintenance charge on your trailer battery but it does not have a specific pin to use for this circuit. You would just need to pick an…

view full answer...

Answer 2

The grommets included with the Spectro Junction Box, #38656, have an inner diameter of .603 inches. These grommets would definitely be too small for your larger output cable and would be a tight fit with your input cable. I checked our other junction…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Distance Between Mounting Holes on the Junction Box part # 38656

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching