Interchangeable Hitch Ball and Ball Mount Recommendation for a 1-1/4 inch Hitch
Question:
I need a straight receiver w/opening 1 1/4 ins, Next need2 or 3 in balls attached to receiver, that goes into the hitch. Or maybe you could recom. me to someone. Either way6 I hope you have a way. Thanking you in advanced. sherron I kmnow we hsave a lot of smaller cars, so where are they getting their receiver and hitch?? I hope my email works right.If not, and you have good news,
asked by: Sherron P
Expert Reply:
Sounds like you are looking for a multi-ball ball mount similar to the part # PS80425 but for a 1-1/4 inch hitch instead.
I have a solution for you, but there are no ball mounts like that for the 1-1/4 inch hitches.
Instead you would need a ball mount like the part # C45019 which fits 1-1/4 inch hitches and then an interchangeable ball set like part # 800B.
Products Referenced in This Question
Convert-A-Ball Interchangeable Ball Set - 1-7/8", 2" Balls - 3/4" XL Shank - Nickel
- Trailer Hitch Ball
- Trailer Hitch Ball
- Interchangeable Ball Set
- Nickel-Plated Steel
- 1-7/8 Inch Diameter Ball
- 2 Inch Diameter Ball
- 2-1/4 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Convert-A-Ball
more information >
Curt Class I Drawbar - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 1 Inch
- Rise - 1 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- CURT
more information >
Product Page this Question was Asked From
Pro Series Tri-Ball Mount for 2" Hitches - 1-7/8", 2", 2-5/16" Balls - Black
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- 2-5/16 Inch Ball
- Three Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 0 Inch
- Rise - 0 Inch
- Fits 2 Inch Hitch
- 10000 lbs GTW
- Class IV
- Pro Series
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Article: How to Measure for Trailer Hitch Drop
- Article: How to Measure a Trailer Axle
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: Tips on How To Tow a Trailer
- Q&A: How To Determine if the 2018 Toyota Highlander Has A Tow Package For Trailer Wiring
- Q&A: Trunnion Spring Bar Length in the Curt Trunnion Weight Distribution System part # 17302
- Q&A: How Far Back From Ball Center Should L-Brackets of Reese Weight Distribution # RE44FR/49913 Install
- Q&A: Trailer Tires are Wearing On the Inside Tread with Low Miles on the Tires
- Q&A: Ball Mount Recommendation for Towing Coachmen RV
- Q&A: How Do I Know How High The Ball Should Sit Above the Ground
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: What Does the 12 Volt Power Wire Do on the 2012 Honda CRV Wiring Kit by Curt
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams