Hardware Kit for Mounting a Thule Adventurer 650 Cargo Box on Yakima Crossbars

Question

Question:

I have an Adventurer 650 cargo box and I have Yakima round roof crossbars. What is the recommended attachment method for this? Do they make a QuickGrip clamp for this application? Is it part #TH04997? Thanks for your help

asked by: Pat

0

Expert Reply:

I spoke with my contact at Thule. He stated that the Thule QM3 Quick On-Off Mounting Hardware Kit for Adventurer Cargo Box, # TH04997, will fit your 650 Adventurer Cargo Box and it will fit the Yakima round load bars.

expert reply by: Michael H

0

Answer 1

According to my contact at Thule, the mounting hardware that came with the Thule Summit cargo box was designed to fit round, square and most factory installed crossbars. As long as the crossbars on your 2013 Ford Explorer are not wider than 3-5/8…

view full answer...

Answer 2

As long as the crossbars on your 2012 Honda Odyssey are less than 3-5/8 inches wide the replacement hardware, #TH04997, will fit. The hardware consists of a complete replacement kit. No other parts are needed.

view full answer...

Answer 3

If you can get the number off of the lock core all you need is the part #THKEYNXXX where the X's would equal the lock number. If the key is in the unlocked position the change key of the part #TH450200 would insert and then allow the core to…

view full answer...

Answer 4

I can certainly help you out. The hardware used on the Thule Adventurer is #TH04997 that you have referenced. There is a specific order in which all of the parts will go on the crossbars. I have included a picture that shows how all of the parts go…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 11

Hi there Bo, we do have the trailer hitch and wiring you need for your 2005 GMC Yukon. The fits for both are the following: - Curt Trailer Hitch Receiver #C15324 - Tail Light Converter with 4-Pole Flat Trailer Connector #C59236 The hitch is a Class V…

view full answer...

Answer 12

I spoke with my contact at Reese and since the Friction Sway Control Kit, #83660, has not been tested on a Rockwood Freedom Pop-Up Camper trailer, we can not guarantee that the support mount on your trailer would not interfere with the operation of…

view full answer...