Bearing Buddy for Trailer Hub that Has Bearing Number of 25580

Question

Question:

What is the bearing buddy part number for 25580 bearing

asked by: Bearing B

0

Expert Reply:

Since you didn't specify which bearing of your hub is 25580 I am fairly certain that the correct Bearing Buddy you would need would be the part # BB2717. But you will need to measure the bore where you old grease cap sits currently to verify that it is 2.71 inches in diameter.

expert reply by: Jameson C

0

Answer 1

Thank you very much for your follow up question. The Bearing Buddy Bearing Protectors #BB2717 are designed to work with outer bearing model 14125A and outer bearing cup (race) model 14276, which are commonly found on 7,000-lb Dexter axles. Most…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

To determine which brake assemblies would be needed, you will need to measure your existing brake drums as shown in the provided photo. Since your trailer has a 14,000 lb capacity, you most likely have tandem 7,000 lb axles, which typically use a…

view full answer...

Answer 9

The 205/65-10 and the 20.5 x 8-10 would be very close in size. Assuming that 20.5 is the diameter of the tire and 8 is the width. The Kenda 205/65-10 Bias Trailer Tire with 10 inch White Wheel, #AM3H390, for example, is 8.3 inches wide with a…

view full answer...

Answer 10

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 11

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 12

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Bearing Buddy for Trailer Hub that Has Bearing Number of 25580

Product Page this Question was Asked From

Continue Researching