Hole Spacing of Brackets Included in Fulton # F500286 Trailer Jack Mounting Hardware Kit

Question

Question:

I would like to find out what the dimensions of part kit F500286 is. More precisely, the distances between the holes on the bracket and the overall size of the bracket. Also, the diametre of the holes on the bracket. Thank you.

asked by: Andre

0

Expert Reply:

The brackets included in the Fulton # F500286 Replacement Jack Mounting Hardware measure 6-5/16 inches long by 1-5/16 inches long. The hole spacing between the closer holes is 1 inch, the spacing between the group of 4 holes and the further away hole is 2-5/16 inches. The hole diameter is .41 of an inch, just a bit larger than 7/16 of an inch.

I've provided a diagram showing these dimensions.

expert reply by: Mike L

0

click to enlarge

Answer 1

Thanks for sending me your picture; it helped out a lot! Instead of new U-bolts, I would instead suggest the Fulton replacement mounting hardware #F500286. This will be able to accommodate different sized frames of trailers and the threads will be…

view full answer...

Answer 2

I will start with the hubs. You have Dexter 8-248 hubs so the correct replacement is the Dexter Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 #84545BX. This assembly includes the bearings, races and seals. For Bearing Buddy replacements,…

view full answer...

Answer 3

I went out to our warehouse to take a look at the Fulton Replacement Bolt-On Mounting Kit #F500349 referenced in your question. I measured a distance between the two outside bolt holes, horizontally, of right at 5-1/2 inches. Vertically the distance…

view full answer...

Answer 4

In regards to mounting the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301 you'll need a mounting kit like the Bolt-On Mounting Kit for Fulton part #F500349 which contains the mount and the center bolt, nut, and tapered spacer. The only…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

The Hydraulic Line Kit #9579-01 comes with two 18" flex hoses and two 51" steel lines.

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Hole Spacing of Brackets Included in Fulton # F500286 Trailer Jack Mounting Hardware Kit

Product Page this Question was Asked From

Continue Researching