Max Speed Rating for Pewag Snow Cables

Question

Question:

What is the max recommended speed with these particular chains and can I run on bare asphalt? I ask because we get snow and ice in NC but you will run in and out of spots.

asked by: Rick S

0

Expert Reply:

You cannot run tire chains on dry asphalt as that will wear them out incredibly quickly.

The maximum speed you can run the Pewag Cables part # PW1046 is 30-35 miles per hour.

expert reply by: Jameson C

0

Answer 1

According to my contact at Glacier Chains, the maximum speed rating for the Glacier Cable Snow Tire Chains, #PW3010C, is 30 miles per hour unless otherwise stated in the vehicle owners manual. It is important that you check your vehicles owners…

view full answer...

Answer 2

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

M12-1.5 and 1/2"-20 threads are not going to be interchangeable. The diameter of an M12 thread is only going to be 0.4724" while 1/2" threads are going to be 0.500" in diameter. We currently only have 1/2"-20 Lug Nuts…

view full answer...

Answer 6

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 10

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Max Speed Rating for Pewag Snow Cables

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching