Gooseneck Hitch Recommendation for a 2016 Ford F-250 6-3/4 ft Bed

Question

Question:

will the Blue Ox Diamond Hitch # DH1204 fit on my 2016 Ford F250 Super Duty 6 3/4 box the ad says it is for a 2015

asked by: Larry H

0

Expert Reply:

For your 2016 Ford F-250 short bed the Curt part # C60720 has been confirmed as a fit and would work well for you.

expert reply by: Jameson C

0

Answer 1

The Curt EZr Double Lock #C60683 and the Double Lock #C60720 are essentially the same gooseneck system with some minor differences. Mainly, the EZR sits lower by 3/8" in the truck bed, but it's main draw is that it's designed to be a bit…

view full answer...

Answer 2

No, you do not have to remove the bed on your 2015 Ford F-250 to install Curt gooseneck trailer hitch #C60720. The only variation of the installation is that on 2011 and newer model trucks the hitch head needs to be rotated when installed so that…

view full answer...

Answer 3

The Curt Double Lock Flip and Store Underbed Gooseneck Hitch #C60720 is a confirmed fit for your 2015 Ford F-350 Super Duty pickup, for both the 6-3/4-foot and 8-foot beds that do not have the OEM prep kit. This or any other gooseneck hitch should…

view full answer...

Answer 4

The Curt Double Lock, Flip and Store Underbed Gooseneck Hitch w/ Installation Kit - 30,000 lbs #C60720 on your 2012 Ford F-350 with 72 inch bed has some specific instructions for your vehicle. You will want to pay attention to the model year and the…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

The spacing will depend on the axle diameter and on which particular spring hanger kit you use. If you have a 6000 lb 3 inch diameter axle, and you're using the #APT5 hanger kit which includes 7-3/4 inch equalizers and 2-5/8 inch shackle straps…

view full answer...

Gooseneck Hitch Recommendation for a 2016 Ford F-250 6-3/4 ft Bed

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching