Replacement Electric Trailer Brakes for Dexter 7,000 Pound Trailer Axle

Question

Question:

7000 lbs dexter axle 2004 carriage 36extrm 5th wheel rv will this 12-1/4 2-1/2 fit it looks the same as my old one part number 23-428

asked by: Dann D

0

Expert Reply:

For trailer brake assembly # 23-428 to fit the drum will need to have an inner diameter of 12-1/4 inches and a width where the pads touch of 2-1/2 inches. I have included a picture showing these locations in a drum. This brake also mounts on a 4 bolt brake mounting flange. The 12-1/4 by 2-1/2 is not a common size though.

The most common size brakes for a Dexter 7,000 pound axle is going to be 12 x 2 inch that mounts on a 5 bolt flange such as # 23-180 and # 23-181.

expert reply by: Michael H

0

click to enlarge

Answer 1

Electric drum brake assemblies for 6k and 7k axles both use the same 5 bolt mounting pattern. The 7k brakes will have a stronger magnet and will provide more braking. If used on a 6k axle a 7k brake assembly can be too aggressive but it could be…

view full answer...

Answer 2

We have replacement pitch arms for your awning with the part #LC266169 which fits either side of the awning. This would exactly what you'd need to get going!

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...