Can A Hitch Receiver Be Adjusted To Carry a Cargo Carrier More Level
Question:
I have the 13069 Curt Class 3 Trailer Hitch Receiver mounted on my 2012 Subaru Tribeca. I have a wheelchair carrier that I need to mount on the vehicle. The problem is that when the carrier is mounted, it slopes downward without anything loaded onto it. I have mounted the same wheelchair carrier onto other vehicles and do not have this issue. Question: What can I do to make the receiver hitch level?
asked by: John E
Expert Reply:
If it is the carrier that slopes inside the trailer hitch receiver you can try an anti-rattle device, like the Lets Go Aero Anti-Rattle Trailer Hitch Receiver Lock # 63232. This will help keep the carrier snug against the inside of the hitch receiver. Sometimes wheelchair carriers or carriers with ramps will slightly slope downward due to the weight of the carrier.
If the receiver of the Curt Trailer Hitch # C13069 is sloped downward and there are no issues with the vehicle suspension or frame, then that could indicate that the receiver was not welded correctly and the hitch would have to be replaced.
Products Referenced in This Question
Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span
- Trailer Hitch Lock
- Universal Anti-Rattle Lock
- Keyed Unique
- Fits 2 Inch Hitch
- Spring-Loaded Pin
- 3-1/2 Inch Span
- Lets Go Aero
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Anti-Rattle Trailer Hitch Receiver Lock for 2" Hitches - 3-1/2" Span
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: 20x59 Curt Cargo Carrier for 2" Hitches - Steel - Folding - 500 lbs
- Shop: Roof Rack
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Video: Curt Hitch Cargo Carrier Review - 2015 Mazda CX-9
- Shop: Anti-Rattle Hitch Pin for 2" Trailer Hitches
- Shop: CargoSmart Cargo Bag for Hitch Mounted Carrier - Water Resistant - 13 cu ft
- Video: Draw-Tite Max-Frame Trailer Hitch Installation - 2020 Mazda CX-9
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2019 Mazda CX-9
- Video: Lets Go Aero Anti-Rattle Hitch Receiver Lock Review
- Search Results: e98942
- Search Results: trailer light mounting bracket
- Shop: Tire Chains
- Search Results: anti rattle
- Search Results: 4 pole mounting bracket
- Search Results: trailer license plate mount
- Search Results: cargo carrier license plate
- Search Results: trailer light tester
- Q&A: Recommended Hitch and 4-way Connector for a 2021 Mazda CX-9
- Q&A: 2021 Mazda CX-9 Grand Touring Hands Free Lift Gate Disabled with Hitch Installed
- Q&A: How to Wire Illuminated License Plate Holder to Trailer Connector
- Q&A: How To Add a 7-Way Trailer Connector To a 2022 Mazda CX-9
- Q&A: Recommendation for Adding 5-Way Trailer Connector to 2019 Mazda CX-9
- Q&A: Recommendation Trailer Hitch, Wiring, and Towing Setup for 2016 Mazda CX-9
- Q&A: Does Trailer Lighting Ground Through the Hitch Ball
- Video: Viking Solutions Tilt-N-Go II Hauler and Cargo Carrier Review