How to Remove Ventline Roof Vent Screen

Question

Question:

I bought this part for a 2009 Springdale tvl tlr. My question is how do I get the inside screen off, so I can get to the operator arm?? Thanks in Advance,

asked by: Ed M

0

Expert Reply:

You can replace the screen on Ventline Trailer Roof Vent in a few easy steps. Make sure that the screws that hold on the handle are exposed. Remove them and then the handle. Next unscrew the small black piece that holds the switch to the screen assembly. Then remove the 2 screws holding on the screen and pull out the screen. Reverse the process to put in the new screen.

expert reply by: Jameson C

0

Answer 1

If you check out the video I attached to this page you'll see a general guide for removing the screen of a roof vent in the the first minute of the video. This process is basically standard amoung trailer roof vents so this process will be…

view full answer...

Answer 2

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links…

view full answer...

Answer 3

We have a video that outlines the procedure for removing the roof vent screen, click on the provided link to view the video. The procedure will involve removing the interior trim as well as the knob or crank, and then the screen can be removed by…

view full answer...

Answer 4

To remove the screen for the MaxxAir MaxxFan Trailer Roof Vent w/ 12V Fan - Manual Lift - 14-1/4" x 14-1/4" - White, #MA00-04000K, you simply remove it from the 4 mounting tabs. These tabs rotate. I've attached a picture for…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

For your 2018 Ram 2500 with the factory puck system the best 5th Wheel Hitch is the B&W OEM Companion. If you have the 8 foot bed then you will want the fixed 25K #BWRVK3600 and if you have the short 6-1/2 foot bed you will need the 20K Slider…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 11

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 12

Hey Frankie, The bracket for the Timbren Suspension Enhancement System #TFR250SDJ has a locknut in it that makes it feel like the bolt (part #4) is fully tightened when it's not. Their techs have stated that you just have to push past this point…

view full answer...

How to Remove Ventline Roof Vent Screen

Product Page this Question was Asked From

Continue Researching