Availability of Black Trailer Fender for Shorelandr Trailer

Question

Question:

I am looking for a plastic black fender for a 12 inch wheel for my Shorelandr boat trailer. The part number of the fender that seems to be closest to the one currently on my boat is F008542. I only see it in white on your website. Do you have that same style in black? If so, can you email me the part number. I am interested in purchasing it. Thank you

asked by: Dan A

0

Expert Reply:

The closest black fender we have to the # F008542 that you referenced is the part # F008551. This fender is 7.35" wide x 21.8" long x 6.5" tall

expert reply by: Jameson C

0

Answer 1

The Fulton Single Axle Trailer Fender with Top Step part #F008542 is only offered in white but we do have a similar option offered in black, part #F008551 or part #F008559.

view full answer...

Answer 2

A 5.30 X 12C tire is going to be your best replacement. If you need the 4 on 4 inch bolt pattern #AM30780 is a good option, or #AM30820 for the 5 on 4-1/2 inch bolt pattern. These both have the wheel and tire included, which you'll need, since…

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 7

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Availability of Black Trailer Fender for Shorelandr Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching