Which Lights will Illuminate on the Tester # I26 When Brakes are Applied

Question

Question:

so what led should light when yhe brake light is activated?

asked by: Packy

1

Helpful Expert Reply:

When your brake lights are pressed and you are using the # I26 as a tester the two pins opposite of the jacketed (ground) pin will illuminate. These are the left and right turn/brake light circuits.

expert reply by: Jameson C

1

click to enlarge

Answer 1

The jacketed circuit is the ground. The one right next to that one is the tail light circuit, next to that one is the left turn circuit. And then the last one on the end is the right turn circuit. Check out the picture I attached to see the circuits…

view full answer...

Answer 2

If you are putting a test light like the Curt #I26 on your vehicle-side 4-Way then you may have installed your vehicle-side 4-Way incorrectly. Is your running light indicator blinking when you put your right turn signal on? If this is the case then…

view full answer...

Answer 3

We do have a wiring harness for your 2023 Hyundai Palisade. I recommend the Curt T-Connector #C43FV. This will plug in behind the driver and passenger side tail lights, and will not require any cutting of the vehicles harness. You will have to run a…

view full answer...

Answer 4

The Curt T-Connector Vehicle Wiring Harness #C43FV is custom fit for your 2023 Hyundai Palisade. This has OEM style connectors to connect to your tail light wiring harness. It will give you a 4-way flat but will require running a power wire to the…

view full answer...

Answer 5

The Curt T-Connector Vehicle Wiring Harness #C43FV is custom fit for your 2023 Hyundai Palisade. This uses the factory style connectors used on the tail lights for your Palisade so you will not have to splice any of your trailer wiring. It does…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 12

For some reason Toyota isn't very forthcoming with how to figure out if you have the tow package or not. From my understanding all of the V6 models of the 2019 Toyota Highlander have the tow package but it isn't specified as to what else…

view full answer...

Which Lights will Illuminate on the Tester # I26 When Brakes are Applied

Product Page this Question was Asked From

Continue Researching