How to Measure a Hub Bore Diameter to Determine What Size Bearing Buddies Fit a Trailer Hub

Question

Question:

What size buddies to buy for a Spartan Sport trailer either 2.08 or 2.04

asked by: Duane L

0

Expert Reply:

To find the correct size Bearing Buddies you can take a set of calipers, dial or digital, and measure the diameter of the hub bore. Part # BB2047 fits a bore size of 2.047 inches. Part # BB2080 fits a hub with a 2.080 inch bore. You will need to measure your hubs to see what size they need.

expert reply by: Patrick B

0

Answer 1

The Dexter part number 023-357-00 is a 12x2 electric brake assembly. The correct RH assembly to use to replace what you have would be the part #23-459 and for the LH assembly you would want the part #23-458 if you have 6K axles. If you have 7k axles…

view full answer...

Answer 2

It sounds like you are talking about a latch pin which would go through the latch and prevent it from opening. It isn't a necessary part but usually what people do with the latch holes is use a latch lock. I recommend Master Lock Adjustable…

view full answer...

Answer 3

For Atwood coupler 80101 a latch lock such as #e98886 will not work. You would need to use a coupler lock such as #FA86-0015-318. Or if you have coupler 80101 then what you could do is use a longer latch lock, #e98888, and put it vertically through…

view full answer...

Answer 4

I only had one photo of yours come through so it is a little hard to tell but you should be able to add your padlock style coupler lock, like the Master Lock #605DAT, to keep your coupler from opening. Attached is a review video of the discontinued…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

The AT15775 part that you referenced was a replacement latch repair kit from Atwood for yoke style A-frame couplers. This kit is no longer available. Atwood was recently bought out and their parts are becoming more and more difficult to find, so your…

view full answer...

Answer 7

I took a look at our yoke-style coupler #CA-5210-B and there doesn't seem to be any type of adjustments that can be made for the coupler to sit more snug on the hitch ball. I would check to make sure that your coupler is cleaned out and free from…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 12

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

How to Measure a Hub Bore Diameter to Determine What Size Bearing Buddies Fit a Trailer Hub

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching