Kodiac Rotor Part # KHR12D Bearings and Brake Pad Recommendation

Question

Question:

Greetings, I am looking to replace my kodiac 12inch disks. I am a little confused as to what bearings and pads go with the rotors. Can you help.

asked by: Bill C

1

Helpful Expert Reply:

The Kodiak 12" Hub-and-Rotor Assembly # KHR12D that you referenced requires an inner bearing of # 25580 and an outer bearing of # 15123.

For a set of brake pads you would want the part # K225CP.

expert reply by: Jameson C

1

Answer 1

When replacing the disk brake rotors on your trailer it is recommended that you also replace your bearings, races and seals at the same time. This will ensure that all components are new and in good order and will prevent the need to dismantle your…

view full answer...

Answer 2

I do have a way to help you get the correct replacement rotor hub for your 2004 Four Winns trailer, but unfortunately we do not have a list of parts on trailers. Usually we can help you get the correct replacement parts based off of the weight…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Kodiac Rotor Part # KHR12D Bearings and Brake Pad Recommendation

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching