How Tall is the Ball Part Only for Curt 1-7/8 Inch Ball 40001

Question

Question:

Hello, Can you tell me the height of the hitch ball for part Code: C40001?

asked by: Tom M

1

Helpful Expert Reply:

I went out to the warehouse and pulled Curt ball # C40001 to measure it for you. The height of the ball from the ball mount platform to the top of the ball is 2.619 inches which is just a hair under 2-5/8 inches.

expert reply by: Michael H

1

click to enlarge

Answer 1

Yes, the Tekonsha T-One 4-Pole Wiring Harness #118718 will work fine to power LED lights on a trailer or accessory carrier used with your 2019 Mazda CX-3 but it does require the 12V power wire connection in order to function. The plug-in connectors…

view full answer...

Answer 2

With Curt hitch #C11418 installed on a 2016 Mazda CX-3 the lower fascia is still attached elsewhere on the vehicle and it will also be resting on top of the hitch receiver. There isn't room to replace the brackets that were removed to install the…

view full answer...

Answer 3

In order to select the correct amount of rise or drop you would need you will need to take a couple measurements. The goal is to have your trailer sit as level as possible. The first thing you will need to do is park your tow vehicle on level ground…

view full answer...

Answer 4

Officially we have to recommend that you always stay with the recommendation of the manufacturer on towing as they are who the warranty of the vehicle is with and they are who would have tested the vehicle for towing. That being said we realize that…

view full answer...

Answer 5

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 6

With Class I hitches like the Draw Tite part #24933 that you referenced you have to use the ball mount that the hitch manufacturer requires which in this case is the Draw Tite part #3593. Then for hitch balls you'd want the part #19258 for a 2…

view full answer...

Answer 7

For a bike rack the Draw Tite part #24933 is the better choice as Curt requires a stabilizer strap like part #18050 with their Class I hitches when carrying a non-supported load like a bike rack. You'll be much happier with the Draw Tite over the…

view full answer...

Answer 8

Between the two hitches that fit your 2018 Mazda CX-3 the Curt, part #C11418, is tucked under the rear bumper by about an inch more than the Draw-Tite, part #24933. Although I feel like the Curt is still more obvious to the eye because it has the…

view full answer...

Answer 9

Although both the Draw-Tite #24933 and the Curt #C11418 Class I hitches look pretty different, in all the ways that matter they're very similar. Both hitches are a concealed mount, so the crossbars are hidden behind the vehicle bumper with the…

view full answer...

Answer 10

Actually Curt stopped requiring the stabilizer straps with bike racks and other non-supported hitch accessories with their hitches like the #C11418 that fits your 2019 Mazda CX-3. It was an extra precaution they took back in the day but recently…

view full answer...

Answer 11

The distance from the center of the pin hole to the end of the shank that slides into the hitch is 1-7/8 inches.

view full answer...

Answer 12

The recommended 2 inch Euro style ball mount for Curt trailer hitch #C11352 on a 2015 Nissan Altima is #C45572. I went out to the warehouse and pulled one to take some measurements. From the center of the pin hole to the part of the shank where it…

view full answer...

How Tall is the Ball Part Only for Curt 1-7/8 Inch Ball 40001

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching