Grease Cap Recommendation to Replace Cap that Measures 1.90 Inches

Question

Question:

I have a 1.90 outside diameter grease cap and the inside is 1.80 diameter will this cap work

asked by: Bryan

0

Expert Reply:

You would want the part # F001524 which has an outer diameter of 1.943 inches. This would install in your hub and provide a nice tight fit.

The part # F001503 would be too small and wouldn't stay in your trailer hub.

expert reply by: Jameson C

0

Answer 1

For your Glo-Brite 118A amber light the replacement lens that will fit is the Optronics #A44AB; the lights themselves are the Optronics #MC44AB. The Glo-Brite 117R can use replacement lens #A44RB while the light is #MC44RB. I've added links to…

view full answer...

Answer 2

The Replacement Tail Light Lens #A40RB is not held on with screws. The outer bezel housing of the 4-1/2" Round Trailer Stop, Turn and Tail Light, Flange Mount, 3-Function #ST40RB for instance has the housing held by screws and the lens is held…

view full answer...

Answer 3

You can measure either the outer diameter of the part of the dust cap that fits into the hub OR the inner diameter of the hub where the dust cap goes using calipers such as #PTW80157. Calipers are needed because the measurement has to be as accurate…

view full answer...

Answer 4

For your hub that has a bore of 1.938 you would want the part #F001524 which has an outer diameter of 1.943 inches. This will fit your hub well.

view full answer...

Answer 5

Are you sure you didn't order a cap for a 1.968 hub bore? We don't offer a cap for a 1.986 bore. The next size down would be for a 1.943 bore, part #F001524 which would be the correct fit for a 1.94 bore. Keep in mind, the dust caps are meant…

view full answer...

Answer 6

If there is any corrosion built up on the hub, it could be built up corrosion built up on the hub bore making the hole read smaller. Grease caps do not have to be very deep. They only have to go in far enough to fit snug and tight inside the hub…

view full answer...

Answer 7

We have one option that may work for you as it is very close to 1.934 inches, but there isn't a cap available with that exact measurement. The cap with the closest diameter to that is the Fulton Grease Cap #F001524. This cap has a 1.943 inch…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Grease Cap Recommendation to Replace Cap that Measures 1.90 Inches

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching