Grease Cap Recommendation for Trailer Hub with 1.938 inch Bore

Question

Question:

I have an old utility trailer which has an outer bearing race #09195, the diameter of which should be 1.938. I am in need of a dust cap that would fit this. The closest one I can find on your site is F001527, which has a listed diameter of 1.957. That might be too big. The one that is on there now measures roughly 1.945. Is there anything closer to that diameter, or might the 1527 work for that?

asked by: Kevin

1

Helpful Expert Reply:

For your hub that has a bore of 1.938 you would want the part # F001524 which has an outer diameter of 1.943 inches. This will fit your hub well.

expert reply by: Jameson C

1

Answer 1

You can measure either the outer diameter of the part of the dust cap that fits into the hub OR the inner diameter of the hub where the dust cap goes using calipers such as #PTW80157. Calipers are needed because the measurement has to be as…

view full answer...

Answer 2

Are you sure you didn't order a cap for a 1.968 hub bore? We don't offer a cap for a 1.986 bore. The next size down would be for a 1.943 bore, part #F001524 which would be the correct fit for a 1.94 bore. Keep in mind, the dust caps…

view full answer...

Answer 3

A 4.80-12 size tire will only fit on a 12 x 4-inch rim such as the one in wheel/tire part #AM30670 and wheel #AM22319HWT. The smaller tire size 4.80-8 like item #AM10002 that you referenced will fit an 8 x 3-3/4-inch wide rim but again not a 12 x…

view full answer...

Answer 4

The Karrier S-Trail tire you mentioned, part #AM10140 would most likely fit on your trailer. They are about the same diameter as your existing tires, but are about an inch wider. You would want to check the distance between your existing tires and…

view full answer...

Answer 5

If there is any corrosion built up on the hub, it could be built up corrosion built up on the hub bore making the hole read smaller. Grease caps do not have to be very deep. They only have to go in far enough to fit snug and tight inside the hub…

view full answer...

Answer 6

You would want the part #F001524 which has an outer diameter of 1.943 inches. This would install in your hub and provide a nice tight fit. The part #F001503 would be too small and wouldn't stay in your trailer hub.

view full answer...

Answer 7

The closest grease cap we offer to what you would need is the part #F001524 that is designed to fit hubs that are 1.943 inches. 1-15/16 inches in decimal form is 1.9375 inches.

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Grease Cap Recommendation for Trailer Hub with 1.938 inch Bore

Product Page this Question was Asked From

Continue Researching